Welcome to Friends of Prasar Bharati

Technical illustrations · Direct-to-Mobile

Direct-to-Mobile Broadcasting in Three Engineering Diagrams

How a programme travels from Akashvani and Doordarshan studios to a smartphone, how OFDM carries it over the air, and how a hybrid HPHT/LPLT single frequency network covers a city.

November 2026

Contents

About these diagrams

These three engineering block diagrams accompany the technical article Direct-to-Mobile Broadcasting: The Next Technological Revolution in Indian Broadcasting. Each one follows the signal through a different part of the system, with the signal paths and major equipment clearly identified.

  • Figure 1 follows a programme from the studio to the smartphone, through the five stages described in Section 4 of the article.
  • Figure 2 shows the digital signal processing inside an ATSC 3.0 OFDM transmitter and receiver (Section 6).
  • Figure 3 shows how a hybrid HPHT/LPLT single frequency network combines wide-area and local coverage (Sections 7 and 8).

Note. These are conceptual engineering illustrations, not as-built schematics of Prasar Bharati’s trial equipment.

Figure 1Complete Direct-to-Mobile (D2M) System Architecture

Content generation to mobile reception

Figure 1. Architecture of an ATSC 3.0-based D2M system Five stages from left to right: content generation at Akashvani and Doordarshan studios; encoding and multiplexing; the ATSC 3.0 transmission system (broadcast gateway, digital exciter, RF power amplifier, output filter); the RF transmission network (broadcast antenna at an HPHT, LPLT or BRH site radiating the D2M RF signal in the 470-582 MHz range); and the mobile receiving system (receiving antenna and RF front end, tuner and OFDM demodulation, error correction, audio-video decoding and playback). 1 Content generation Section 4.1 2 Encoding and multiplexing Section 4.2 3 ATSC 3.0 transmission Section 4.3 4 RF transmission network Section 4.4 5 Mobile receiving system Section 4.5 Akashvani and Doordarshan studios Audio and video processing Digital encoding HEVC video, advanced audio IP encapsulation and multiplexing Broadcast gateway Digital exciter FEC and OFDM modulation RF power amplifier Output filter Receiving antenna and RF front end Tuner and OFDM demodulation Error correction Audio-video decoding and playback Other sources: news and regional centres, educational and government providers, authorised private broadcasters Several television, audio and data services share one RF channel D2M RF signal 470–582 MHz Broadcast antenna at HPHT, LPLT or BRH sites

Scroll sideways to see the whole diagram

Figure 1Architecture of an ATSC 3.0-based D2M system, from programme generation at Akashvani and Doordarshan studios to playback on a compatible smartphone. The numbered stages correspond to Sections 4.1 to 4.5 of the article.

Programme content generated at Akashvani and Doordarshan is digitally processed, encoded and multiplexed. The ATSC 3.0 transmission system converts it into an RF signal for transmission. Compatible smartphones receive, decode and reproduce the programmes.

The five stages

  1. Content generation

    Programmes are produced at Akashvani and Doordarshan studios, news and regional centres, educational and government providers and authorised private broadcasters, then processed for digital distribution. Section 4.1

  2. Encoding and multiplexing

    Video is compressed with HEVC and audio with advanced audio coding. The encoded services are carried in IP streams, so several television, audio and data services can share one RF channel. Section 4.2

  3. ATSC 3.0 transmission system

    The broadcast gateway feeds the digital exciter, which applies forward error correction and OFDM modulation. The RF power amplifier and output filter deliver the signal to the antenna. Section 4.3

  4. RF transmission network

    The antenna at an HPHT, LPLT or Broadcast Radio Head site radiates the D2M signal in the 470–582 MHz range. Section 4.4

  5. Mobile receiving system

    In a compatible phone, the antenna, tuner and OFDM demodulator recover the signal, and error correction and audio-video decoding bring the programme to the screen. Section 4.5

Important: D2M reception is not automatically possible on every existing smartphone. The phone needs dedicated receiving hardware and software.

Figure 2ATSC 3.0 OFDM Transmitter and Receiver Architecture

Digital signal processing and RF transmission

OFDM divides the channel into many closely spaced orthogonal subcarriers, each carrying part of the data. The transmitter builds the OFDM signal stage by stage, and the receiver undoes each stage in reverse order. In the diagram the transmitter reads downwards and the receiver upwards, so every receiver stage sits beside the transmitter stage it reverses.

Figure 2. Simplified ATSC 3.0 OFDM transmitter and receiver Transmitter, reading down: digital input data, channel coding (FEC), bit interleaving, QAM symbol mapping, subcarrier mapping and pilot insertion, IFFT, guard interval insertion, DAC and RF upconversion, RF power amplifier, transmitting antenna. The signal crosses the radio channel. Receiver, reading up: receiving antenna, RF front end and tuner, RF downconversion and ADC, guard interval removal, FFT, channel estimation and equalisation, QAM demapping, bit deinterleaving, FEC decoding, decoded audio and video. A time and frequency synchronisation block takes the digitised signal and controls guard interval removal and the FFT. TRANSMITTER exciter and transmitter RECEIVER compatible smartphone Digital input data Channel coding (FEC) Bit interleaving QAM symbol mapping Subcarrier mapping and pilot insertion IFFT Guard interval insertion DAC and RF upconversion RF power amplifier Transmitting antenna Decoded audio and video FEC decoding Bit deinterleaving QAM demapping Channel estimation and equalisation FFT Guard interval removal RF downconversion and ADC RF front end and tuner Receiving antenna Coding (BICM) OFDM modulation RF Decoding (BICM) OFDM demodulation RF Time and frequency synchronisation Each receiver stage reverses the transmitter stage beside it Radio channel multipath and noise

Scroll sideways to see the whole diagram

Figure 2Simplified ATSC 3.0 OFDM transmitter and receiver. The IFFT/FFT and guard-interval stages are shaded. BICM: bit-interleaved coded modulation.

What the important blocks do

BlockWhereFunction
FECBothAdds redundancy at the transmitter so that the receiver can correct transmission errors
Bit interleavingBothSpreads the coded bits apart, so a burst of errors becomes scattered errors that FEC can correct
QAM mappingTransmitterConverts bits into modulation symbols
Pilot insertionTransmitterAdds known reference subcarriers that let the receiver measure the channel
IFFTTransmitterGenerates the OFDM time-domain signal
Guard intervalBothReduces inter-symbol interference
RF upconversionTransmitterConverts the signal to the assigned RF channel
SynchronisationReceiverLocks the receiver’s timing and frequency to the signal, so the guard interval is removed and the FFT window placed correctly
FFTReceiverRecovers OFDM subcarriers at the receiver
EqualisationReceiverCompensates for channel distortion

The guard interval is also what makes a single frequency network possible: signals from several transmitters that arrive within it are treated as echoes and combined, not as interference.

Figure 3Hybrid HPHT/LPLT Single Frequency Network (SFN)

Wide-area coverage with local coverage enhancement

Figure 3. Hybrid HPHT/LPLT single frequency network A central D2M content distribution centre feeds an IP or broadcast distribution network, which delivers an identical programme stream to one HPHT transmitter and three LPLT transmitters. A GNSS time and frequency reference gives every site common timing. The HPHT transmitter feeds a high tower antenna for wide-area coverage; the LPLT transmitters feed local antennas for urban coverage and gap filling. All sites radiate on a common SFN RF channel, and compatible mobile receivers combine signals from several sites within the guard interval. Central D2M content distribution centre encoders, multiplexer and broadcast gateway IP / broadcast distribution network fibre, microwave or satellite links GNSS time and frequency reference 1 PPS and 10 MHz to every site Identical programme stream to every site HPHT transmitter high power, high tower LPLT transmitter 1 low power, low tower LPLT transmitter 2 low power, low tower LPLT transmitter 3 low power, low tower High tower antenna wide-area coverage Local antenna 1 urban and gap filling Local antenna 2 urban and gap filling Local antenna 3 urban and gap filling Common SFN RF channel every site radiates the same signal, on the same frequency, at the same time Compatible mobile receivers signals from several sites combine within the guard interval

Scroll sideways to see the whole diagram

Figure 3Hybrid HPHT/LPLT single frequency network. Every transmitter receives the same programme stream and a common GNSS timing reference, so all sites radiate an identical signal on the same RF channel at the same time.
  • HPHT provides wide geographical coverage.
  • LPLT transmitters improve reception in urban areas and coverage gaps.
  • All participating transmitters use the same assigned RF channel.
  • Synchronisation is essential to successful SFN operation.
  • Compatible mobile devices receive the transmitted signal.

The hybrid HPHT/LPLT architecture demonstrated in Delhi is particularly significant because it combines broad-area and local-area coverage using an SFN approach.